Cypress CY7C1380C Manual de usuario

Busca en linea o descarga Manual de usuario para No Cypress CY7C1380C. Cypress CY7C1380C User's Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 36
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
18-Mb (512K x 36/1M x 18) Pipelined SRAM
CY7C1380C
CY7C1382C
Cypress Semiconductor Corporation 3901 North First Street San Jose, CA 95134 408-943-2600
Document #: 38-05237 Rev. *D Revised February 26, 2004
Features
Supports bus operation up to 250 MHz
Available speed grades are 250, 225, 200,166 and
133MHz
Registered inputs and outputs for pipelined operation
3.3V core power supply
2.5V / 3.3V I/O operation
Fast clock-to-output times
2.6 ns (for 250-MHz device)
2.8 ns (for 225-MHz device)
3.0 ns (for 200-MHz device)
3.4 ns (for 166-MHz device)
4.2 ns (for 133-MHz device)
Provide high-performance 3-1-1-1 access rate
User-selectable burst counter supporting Intel
®
Pentium interleaved or linear burst sequences
Separate processor and controller address strobes
Synchronous self-timed writes
Asynchronous output enable
Single Cycle Chip Deselect
Offered in JEDEC-standard 100-pin TQFP, 119-ball BGA
and 165-Ball fBGA packages
IEEE 1149.1 JTAG-Compatible Boundary Scan
“ZZ” Sleep Mode Option
Functional Description
[1]
The CY7C1380C/CY7C1382C SRAM integrates 524,288 x 36
and 1,048,576 x 18 SRAM cells with advanced synchronous
peripheral circuitry and a two-bit counter for internal burst
operation. All synchronous inputs are gated by registers
controlled by a positive-edge-triggered Clock Input (CLK). The
synchronous inputs include all addresses, all data inputs,
address-pipelining Chip Enable (
CE
1
), depth-expansion Chip
Enables (CE
2
and
CE
3
[2]
), Burst Control inputs (
ADSC
,
ADSP
,
and
ADV
), Write Enables (
BW
X
, and
BWE
), and Global Write
(
GW
). Asynchronous inputs include the Output Enable (
OE
)
and the ZZ pin.
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (
ADSP
) or
Address Strobe Controller (
ADSC
) are active. Subsequent
burst addresses can be internally generated as controlled by
the Advance pin (
ADV
).
Address, data inputs, and write controls are registered on-chip
to initiate a self-timed Write cycle.This part supports Byte Write
operations (see Pin Descriptions and Truth Table for further
details). Write cycles can be one to two or four bytes wide as
controlled by the byte write control inputs.
GW
when active
LOW
causes all bytes to be written.
The CY7C1380C/CY7C1382C operates from a +3.3V core
power supply while all outputs may operate with either a +2.5
or +3.3V supply. All inputs and outputs are JEDEC-standard
JESD8-5-compatible.
Selection Guide
250 MHz 225 MHz 200 MHz 167 MHz 133 MHz Unit
Maximum Access Time 2.6 2.8 3.0 3.4 4.2 ns
Maximum Operating Current 350 325 300 275 245 mA
Maximum CMOS Standby Current 70 70 70 70 70 mA
Shaded areas contain advance information.
Please contact your local Cypress sales representative for availability of these parts.
Notes:
1. For best–practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
2. CE
3
, CE
2
are for TQFP and 165 fBGA package only. 119 BGA is offered only in 1 Chip Enable.
[+] Feedback
Vista de pagina 0
1 2 3 4 5 6 ... 35 36

Indice de contenidos

Pagina 1 - CY7C1382C

18-Mb (512K x 36/1M x 18) Pipelined SRAMCY7C1380CCY7C1382CCypress Semiconductor Corporation • 3901 North First Street • San Jose, CA 95134 • 408-94

Pagina 2 - [+] Feedback

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 10 of 36ADSP84 A4 B9 Input-SynchronousAddress Strobe from Processor, sampled on the rising edge of

Pagina 3 - Pin Configurations

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 11 of 36VDDQ4,11,20,27,54,61,70,77A1,A7,F1,F7,J1,J7,M1,M7,U1,U7C3,C9,D3,D9,E3,E9,F3,F9,G3,G9,J3,J9

Pagina 4

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 12 of 36Functional OverviewAll synchronous inputs pass through input registers controlledby the ri

Pagina 5 - 165-ball fBGA

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 13 of 36Asserting ADV LOW at clock rise will automatically incrementthe burst counter to the next

Pagina 6

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 14 of 36READ Cycle, Continue Burst Next H X X L X H L H H L-H Tri-StateWRITE Cycle, Continue Burst

Pagina 7

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 15 of 36IEEE 1149.1 Serial Boundary Scan (JTAG)The CY7C1380C incorporates a serial boundary scan t

Pagina 8

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 16 of 36TDI and TDO balls as shown in the Tap Controller BlockDiagram. Upon power-up, the instruct

Pagina 9

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 17 of 36Note that since the PRELOAD part of the command is notimplemented, putting the TAP to the

Pagina 10

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 18 of 363.3V TAP AC Test ConditionsInput pulse levels ... ...

Pagina 11

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 19 of 36 Identification Register DefinitionsINSTRUCTION FIELDCY7C1380C(512KX36)CY7C1382C(1MX18)DES

Pagina 12

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 2 of 3612Logic Block Diagram – CY7C1380C (512K x 36)ADDRESSREGISTERADVCLKBURSTCOUNTER ANDLOGICCLRQ

Pagina 13

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 20 of 36119-Ball BGA Boundary Scan Order CY7C1380C (512K x 36)BIT# BALL ID BIT# BALL ID1K437 B22H4

Pagina 14

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 21 of 36CY7C1382C (1M x 18)BIT# BALL ID BIT# BALL ID1K437 B22H438 P43M439 N44F440 R65B441 T56A442

Pagina 15

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 22 of 36165-Ball fBGA Boundary Scan OrderCY7C1380C (512K x 36)BIT# BALL ID BIT# BALL ID1B637N62B73

Pagina 16

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 23 of 36CY7C1382C (1M x 18)BIT# BALL ID BIT# BALL ID0B636N61B737R62A738P63B839R44A840R35B941P46A94

Pagina 17

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 24 of 36Maximum Ratings(Above which the useful life may be impaired. For user guide-lines, not tes

Pagina 18 - VSS to 2.5V

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 25 of 36ISB3Automatic CE Power-down Current—CMOS InputsVDD = Max, Device Deselected, or VIN ≤ 0.3V

Pagina 19

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 26 of 36AC Test Loads and Waveforms OUTPUTR = 317ΩR = 351Ω5pFINCLUDINGJIG ANDSCOPE(a)(b)OUTPUTRL=

Pagina 20

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 27 of 36Switching Characteristics Over the Operating Range[19, 20]Parameter Description250 MHz 225

Pagina 21

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 28 of 36Switching WaveformsRead Cycle Timing[21]Notes: 21. On this diagram, when CE is LOW: CE1 is

Pagina 22

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 29 of 36Write Cycle Timing[21, 22]Switching Waveforms (continued)tCYCtCLCLKADSPtADHtADSADDRESStCHO

Pagina 23

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 3 of 36Pin Configurations AAAAA1A0NC / 72MNC / 36MVSSVDDAAAAAAAADQPBDQBDQBVDDQVSSQDQBDQBDQBDQBVSSQ

Pagina 24

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 30 of 36Read/Write Cycle Timing[21, 23, 24]Note: 23.The data bus (Q) remains in high-Z following a

Pagina 25

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 31 of 36Notes: 25. Device must be deselected when entering ZZ mode. See Cycle Descriptions table f

Pagina 26

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 32 of 36 Ordering InformationSpeed(MHz) Ordering CodePackageName Part and Package TypeOperatingRan

Pagina 27

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 33 of 36© Cypress Semiconductor Corporation, 2004. The information contained herein is subject to

Pagina 28

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 34 of 36Package Diagrams (continued)51-85115-*B119-Lead PBGA (14 x 22 x 2.4 mm) BG119[+] Feedback

Pagina 29

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 35 of 36Package Diagrams (continued)i486 is a trademark, and Intel and Pentium are registered tra

Pagina 30

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 36 of 36Document History PageDocument Title: CY7C1380C/CY7C1382C 18-Mb (512K x 36/1M x 18) Pipel

Pagina 31

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 4 of 36Pin Configurations (continued)2345671ABCDEFGHJKLMNPRTUVDDQNCNCDQPCDQCDQDDQCDQDAA AAADSPVDD

Pagina 32

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 5 of 36Pin Configurations (continued)165-ball fBGACY7C1380C (512K x 36)234 5671ABCDEFGHJKLMNPRTDO

Pagina 33

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 6 of 36CY7C1380C–Pin DefinitionsName TQFP BGA fBGA I/O DescriptionA0, A1 , A 37,36,32,33,34,35,42,

Pagina 34

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 7 of 36ADSP84 A4 B9 Input-SynchronousAddress Strobe from Processor, sampled on the rising edge of

Pagina 35

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 8 of 36VSSQ5,10,21,26,55,60,71,76- - I/O Ground Ground for the I/O circuitry. VDDQ4,11,20,27,54,61

Pagina 36

CY7C1380CCY7C1382CDocument #: 38-05237 Rev. *D Page 9 of 36CY7C1382C:Pin DefinitionsName TQFP BGA fBGA I/O DescriptionA0, A1 , A 37,36,32,33,34,35,42,

Comentarios a estos manuales

Sin comentarios